Home News

How to Choose the Right Seal?(Component vs Cartridge)

Customer Reviews
KALU is a well-established manufacturing enterprise whose services have met with warm reception for its superior quality and attractive prices.

—— Paul Millsap

I'm Online Chat Now
Company News

How to Choose the Right Seal?(Component vs Cartridge)

How to Choose the Right Seal?(Component vs Cartridge)

Mechanical seals consist of a rotating part and a stationary part, each with a lapped, precision-smooth mating face (see Figure 1). Seal performance is determined primarily by the condition of the faces and the pressure applied to them. Other key factors are vibration, heat and pumpage characteristics. Depending on the application and user's needs, different seal types may be appropriate.For many large centrifugal pumps,users have the option of installing either component or cartridge mechanical seals. Understanding the advantages and limitations of each can help determine the best solution for a particular application.

 

Component Mechanical Seals:

 

Component seals are standard mechanical seals.When users order a replacement, they typically receive a box containing seal faces, holding brackets, O-rings, boots and other parts that require the skills of an experienced pump technician to install and adjust properly.

Incorrect installation and adjustment are common causes of component seal failure. For example, if the seal faces are not properly seated on the shaft or in the seal housing, they will be misaligned. Sliding O-rings and elastomers over shaft shoulders, keyways or sharp edges of the seal housing can also cause damage to these parts and result in incorrect seal tension.

The seal housing often provides limited access, so successful adjustments require precision and accuracy. While an experienced pump technician can successfully install and adjust any component seal, this process provides opportunity for error.

Cartridge Mechanical Seals:

Cartridge seals and component seals use similar components, but the stationary of cartridge seals are preassembled in a housing, and the rotating components are preassembled on a shaft-mounted sleeve that is sealed with an O-ring. The cartridge seal housing typically replaces the gland cover plate and seals to the pump housing with a gasket, an O-ring or other elastomer. Since cartridge mechanical seal components are preassembled onto the sleeve and into the cartridge housing, errors in parts installation are unlikely.

The amount of spring tension applied to the seal faces is an important factor that affects successful seal installation. On component seals, technicians can set this tension manually by adjusting the length of the installed seal spring. With cartridge mechanical seals, the spring tension is preset. To ensure the proper tension, a retaining device holds the rotating and stationary elements in alignment until after the seal is mounted.

While the details of whether a cartridge mechanical seal can be fitted to an application are complex, one criterion is whether the seal installs from the wet side or dry side of the seal chamber. Pumps with a seal that installs from the wet side, behind the impeller, are generally not candidates for cartridge mechanical seals.

In addition, submersible pumps, which are usually fitted with dual component seals, cannot be converted to cartridge mechanical seals because the seals install from the wet side of the pump.

Component vs Cartridge

For end users deciding between a component and cartridge seal, the primary considerations are cost and ease of installation. If a competent pump technician services the pump during overhaul under good working conditions, ease of installation may seem like a minor issue. However, the concern will be for subsequent seal replacement during an emergency outage.Cartridge mechanical seals may cost two to three times component seals, so unless otherwise stated, competitive repair bids are typically for component seals. Despite the higher initial investment, however, a cartridge seal can be a more cost-effective, long-term solution, given the expectation that pump maintenance may require in-service seal replacement. Potential savings accrue from lower labor costs and less production downtime when subsequent seal replacement is needed. Projected savings also include the elimination of seal failures resulting from improper installation of component seals.

 

If users are aiming to find the most cost-effective, long-term solution to pump maintenance and they anticipate in-service seal replacement, a cartridge mechanical seal will likely be a good choice. Incorporating a cartridge mechanical seal also allows the conversion from a packing seal to a mechanical seal. When low initial cost is important, component seals—and a well-trained pump engineer—are the best option.

 

 

Pub Time : 2017-11-30 08:51:48 >> News list
Contact Details
Kalu Industrial Co.,Ltd

Contact Person: Ms. Taylor

Tel: 86-0512-56955713

Fax: 86-0512-56955713

Send your inquiry directly to us (0 / 3000)